TileFast Superior - Off White
* Cost Effective * Polymer Modified * Excellent Bond Strength
Description
Tilefast Superior is a revolutionary polymer modified cement-based thin or thick bed adhesive for internal and external fixing of non porous ceramic tiles. It has been especially formulated for high strength bonding and doesn’t need a liquid additive.
| Suitable Tiles | Suitable Substrates | Colour |
| * Natural Stone | * Concrete/Cement Render | Off White |
| * Bicottura | * Brickwork/Blockwork | Interior | Exterior |
| * Monocottura | * Over Morgan’s Waterproof Membrane | Walls | Walls |
| Floors | Floors |
Precautions
Tilefast Superior is unsuitable for:
- bonding moisture sensitive green marble;
- bonding to painted walls, MDF board, (timber and wax impregnated wood must be sheeted with fibre cement sheeting);
- substrates subject to constant water immersion such as swimming pools.
Surface Preparation
All surfaces to be tiled must be flat and true, free from oil, dirt, grease or any other contaminants. Very porous surfaces should be primed with Plastinex (1 part Plastinex mixed with 4 parts water).
Concrete : New concrete must be allowed to cure for 6 weeks and should have a wood flat finish. When finished with a steel trowel concrete must be acid etched, using Floor Prep.
Cement Render : Render to be left with a wood float finish and allowed to cure for 7 days.
Mixing Tilefast Superior
Add Tilefast Superior to clean water at a ratio of 20 kg to 5 litres of water. Mix product to a smooth paste free from lumps by using a drill that has a speed lower than 300 rpm, or mix by hand. Slacken the adhesive and re-mix after 5-10 minutes.
Pot Life
Tilefast Superior has a pot life of approximately 3 hours at 20oC and 50% relative humidity.
Open Time
Tilefast Superior has an open time of approximately 30 minutes, which can be shortened to just a few minutes by the action of sun, wind, high temperatures or highly absorbent surfaces. Tilers need to constantly check that the adhesive has not formed a surface skin and is still fresh to the touch.
Wetting or priming the substrate prior to tiling prolongs the open time of the adhesive. It is not advisable to wet the adhesive when it has formed a skin as water only increases the rate of cement hydration and will result in an anti adhesive film. Skinned adhesive must always be removed and disposed of.
Application
Always install the tiles in accordance with AS 3958 1:1991 and ensure the backs of the tiles are free of dust. Spread Tilefast Superior evenly across one square metre at a time with a 6 x 6 x 6 notched trowel for walls or a 10 x 10 x 10 notched trowel for floors. The choice of trowel should be governed by the depth of the knobs, grooves or ridges on the back of the tile and the evenness of the substrate.
Lay the tiles with a fair pressure and at right angles to the notched pattern.
The final bed of adhesive should be between 2mm and 4mm. Wall tiles should have a finished joint width of 2mm - 4mm and floor files a finished joint width of 3mm - 6mm. Tiles can be adjusted for approximately 30 minutes after laying.
Coverage
20 kgs of Tilefast Superior will cover approximately 5 - 7 square metres with a 10mm notched trowel for floors and/or 8 - 9 square metres with a 6mm notched trowel.
Dry Time
Tilefast Superior dries in approximately 24 hours at 23oC and 50% relative humidity. It may require longer times to cure for denser tiles and substrates or at installation temperatures below 10oC.
Expansion Joints
Joint Grouting
Grouting may commence after approximately 24 hours (depending on variables such as sun, heat, wind, etc.)
Shelf Life
Tilefast Superior can be stored in the original packaging in a dry elevated position for 12 months.
Packaging
Tilefast Superior is available in 20kg paper sacks.
Morgan’s Quality Policy Statement
Guarantee
Free Technical Advice and Service
| Technical Data | Complies with AS 2358-1990 |
| Product Identity |
| Colour and Type | Off white powder |
| Specific Gravity | 1.85 kg/ltr |
| Toxic Hazard | No |
| Inflammable | No |
| Application Data |
| Mixing ratio | 5:1 |
| Consistency of mix | Very viscous paste |
| Application temperature range | From +10oC to 40oC |
| Cure time | Initial cure in 7 days Full cure in 28 days |
| Ready for traffic | After 24 hours |
| Wall grouting | After 4 hours depending on absorption |
| Floor grouting | After 24 hours |
| Final Performance |
| Damp resistance | Excellent |
| Ageing resistance | Excellent |
| Resistance to solvents and oils | Excellent |
| Resistance to acids and alkalis | Good |
| Resistance to temperature | From -30oC to +90oC |
Correct procedures for use can be found in AS 3958 1 & 2 and must be followed at all times.
